Breaktru Forum
eCigarette Forum => Modding => Topic started by: mamu on September 26, 2014, 08:23:17 PM
-
This project was the request of a friend (dancing disco Dino :laughing:) who does a lot of coil building and testing.
I used a Hammond 1590YBK case (92mm x 92mm x 42mm).
Features:
-Raptor 20A 120W
-Output voltage: 3.3v - 6v
-Reverse polarity protection via externally added p-channel mosfet
-Input overcurrent protection via externally added PTC fuses
-6v (loaded) low voltage cutoff via externally added zener diode
-Power connect/disconnect switch
-Volt/ohm meter power connect/disconnect switch
-LED power on indicator
-LED low battery indicator
Dino needed an ohm meter that it is accurate, reads less than 1 ohm, and reads ohms to the hundredths. I initially was going to use a separate volt meter and ohm meter, but then went on a search to find a combo volt/ohm meter that would meet the requirements I needed. I ended up using Eleaf's combo volt/ohm meter and am powering it with a 4v 250mA LDO.
(http://mamumods.com/pics/rbb01.png)
(http://mamumods.com/pics/rbb02.png)
(http://mamumods.com/pics/rbb03.png)
(http://mamumods.com/pics/rbb04.png)
-
Mamu...
You always amaze me with your creations!
Craftsmanship, beauty, and functionality at their finest.
Like so many of the ideas developed here by the members of the Breaktru Forum, I wonder how long it will be before the Chinese try to copy it.
-
Nice work mamu :rockin smiley: thanks for sharing
I bet some will be tempted to vape off of it :laughing:
-
Cool. Fine job there
-
Thanks guys!
Nice work mamu :rockin smiley: thanks for sharing
I bet some will be tempted to vape off of it :laughing:
lol breaktru - Dino said he's going to take it to a vape meet and vape with it to see people's reactions. I told him he'll need a gooseneck or something. :laughing:
-
ok a box full of kittens with bows
nice build Mamu
-
fainting: I have to do one of these but maybe just unregulated with a Mosfet. Perfect build station setup. Thank you for the great inspiration Mamu..
-
I did an unregulated dual MOSFET coil build/test box for a friend who has a vape shop. I sent him the box and the schematic for it. Hopefully he'll be able to put it into production soon and people will be able to buy it.
I'm calling it Little Sister. :laughing:
Little Sister next to Big Daddy Raptor coil build/test box...
(http://www.mamumods.com/pics/cb1.png)
Checking ohms...
(http://www.mamumods.com/pics/cb2.png)
Checking voltage...
(http://www.mamumods.com/pics/cb3.png)
-
Beautifully done :rockin smiley: Neat and professional :thumbsup:
-
that does not surprise me at all. that is the perfect size as well. Job Well Done as usual Mamu.. ;cheers;
-
Nicely done. I am not sure i would want my fingers that close to some coils though lighting it off :-) Might hurt a little bit. But other than that I would want one anyways. building my first ugly box mod this weekend finally got all the parts in :-)
-
Thanks guys!
-
EVERY time I look at one of your builds, I think "that's so cool, got to make myself one of those". Really enjoy looking, and thanks so for sharing, but you are a major cause of "project bloat" for me! :thumbsup:
Wayne
-
Has to be one of the coolest most creative works ive seen. You have a talent! Please keep up the inspiration!
-
Thanks again, guys.
lol "project bloat" - been there, done that, repeat. :laughing:
-
So neat :applaude: