Breaktru Forum

eCigarette Forum => Atty/Carto/Tank/Rebuildable => Topic started by: zeus17 on July 26, 2013, 03:41:50 PM

Title: microcoils anyone?
Post by: zeus17 on July 26, 2013, 03:41:50 PM
anyone doing microcoils here?

I have been on this builds for a month now and on both my genny clone and chi era clone both are working great....wish vv mods were available in our country...for me to play around ..hahahhaha
Title: Re: microcoils anyone?
Post by: d_walk on July 26, 2013, 05:11:25 PM
I've read some posts on micro-coils. Some use different methods of wicking.
Tell us about your setup
Title: Re: microcoils anyone?
Post by: Pantera on July 26, 2013, 05:18:43 PM
I have not used it yet but seen them.
Here is one by Mister E

(http://i.imgur.com/4ToeZ.gif)
Title: Re: microcoils anyone?
Post by: zeus17 on July 26, 2013, 05:40:01 PM
current set up
2 setups on a kts storm not modified,i guess the only thing done to it was the bottom part to avoid the battery from kinda developing a crater was put a battery contact plate and do some windcrazy of copper wire coming from a wire used for cable tv..dunno if that matters

china era
 1/16 drill bit was used as mold
10 wraps touching each other,,,
**what I did for them to touch try to make them close as possible when winding on the drillbit..place it on the era,remove the drillbit ,fire the thing until it glows,insert the bit again to make adjustments if needed,then squeeze them together using tweezers..remove and fire again see if it glows even,put drillbit again squeeze some more,remove fire,until I get them really close....
wick...cotton,,,soak for 10 minutes with juice..then I enjoy..
results..
a bit warm vape..tons of clouds..

on the mini did clone
14 or 16 wraps..
this time on the hex wrench that was included on the did clone...
same procedure

results..
well...colder vape...really cold...but nice white smoke..

**note did has like 2mm airhole..
era had like 3mm...

juice was like 70/30 ratio/...ill see if I can post pix...I have them on a local group on facebook
Title: Re: microcoils anyone?
Post by: zeus17 on July 26, 2013, 05:41:14 PM
I have not used it yet but seen them.
Here is one by Mister E

(http://i.imgur.com/4ToeZ.gif)

these are spin ecoils right?
sorry cant see them office blocks,,,hahahhaha

I have yet to try this one...

I see how to make the coil...
but cant seem to understand the wick part,,,
Title: Re: microcoils anyone?
Post by: zeus17 on July 26, 2013, 05:48:27 PM
I just wished anything ss mesh or wire was cheap here,,,Nextel and ekowool are to deym expensive,,,and no xc116...so I think cotton is best for me now...
Title: Re: microcoils anyone?
Post by: d_walk on July 26, 2013, 07:45:11 PM
zeus, how did you do your wick? Did you thread it thru the coil or place outside of it?
Title: Re: microcoils anyone?
Post by: zeus17 on July 29, 2013, 10:33:29 AM
I use cotton from a qtip,
then I just roll them by fingertip then slide it in...if it kinda stops I pull a bit out then try again...
I just insert them inside...
I cant seem to be successful if I do it from the outside...either it doesn't wick at all o wick poorly if I do it like outside.....

Title: Re: microcoils anyone?
Post by: Aromaz on August 13, 2013, 10:03:44 AM
Interesting setup:

http://youtu.be/jagnsVTWbdg (http://youtu.be/jagnsVTWbdg)
Title: Re: microcoils anyone?
Post by: zeus17 on August 13, 2013, 10:50:22 AM
sorry I cant post a pix of my own set up currently @ work,,
but here is close to what my current build is.
28ga and 35ga side by side

credits to owner of photo down over at ecf
(http://www.e-cigarette-forum.com/forum/rebuildable-atomizer-systems/416271-micro-coils-increase-vapor-flavor-th-66.html)